Experimental glass blowing for boys
Date: 2024-06-16T00:00:00+00:00
Keywords: Glass blowing and working -- Handbooks; manuals; etc.; Glass blowing and working -- Juvenile literature

The Project Gutenberg eBook of Experimental glass blowing for boys

This ebook is for the use of anyone anywhere in the United States and most other parts of the world at no cost and with almost no restrictions whatsoever. You may copy it, give it away or re-use it under the terms of the Project Gutenberg License included with this ebook or online at www.gutenberg.org. If you are not located in the United States, you will have to check the laws of the country where you are located before using this eBook.

Title: Experimental glass blowing for boys

Author: Carleton John Lynde

Contributor: A. C. Gilbert

Release date: June 16, 2024 [eBook #73841]

Language: English

Original publication: New Haven: The A. C. Gilbert Company, 1920

Credits: Richard Tonsing, deaurider, and the Online Distributed Proofreading Team at https://www.pgdp.net (This file was produced from images generously made available by The Internet Archive)

*** START OF THE PROJECT GUTENBERG EBOOK EXPERIMENTAL GLASS BLOWING FOR BOYS ***

Transcriber’s Note:

New original cover art included with this eBook is granted to the public domain.

Experimental Glass Blowing
FOR BOYS

BY
CARLETON J. LYNDE, Ph. D.
Professor of Physics
MacDonald College, Quebec Province, Canada
Prepared under the direction of
ALFRED C. GILBERT
Yale University, 1909

EXPERIMENTAL GLASS BLOWING

Boys, glass tubes are made in the sizes shown in Fig. 2, and in larger sizes. You will use sizes 2, 4, and 6 in the following experiments.

Experiment 1. Fun bending glass.

FIG. 2

SIZES OF GLASS TUBING

Hold a piece of No. 2, with both hands, in the flame of the alcohol lamp, and turn it constantly (Fig. 3). Do you find that when the glass becomes nearly red hot, it becomes soft and bends easily?

FIG. 3

HEATING GLASS TO SOFTEN IT

Take the tube out of the flame, bend it into any shape you wish (Fig. 4), and allow it to cool. Do you find that the glass hardens when it cools and retains the bent shape?

Heat the tube near the first bend, turn it constantly, take it out of the flame, and make another bend.

Repeat this and make all kinds of fantastic shapes.

Place all hot glass on the cooling blocks, not on the table.

Glass is used in many, many ways by the human race; for example, to make bottles, tumblers, window glass, and so on, and all of these uses depend upon the facts which you have just illustrated, namely, that glass becomes soft when heated and hard when cooled again.

FIG. 4

BENDING GLASS

THE LAMP

The wick should be cut straight across and should project above the wick holder about ⅛ inch (Fig. 5), or a little more if you require more heat. Burn wood alcohol or grain alcohol, because they give flames without soot or smoke. Fill the lamp to within a ½ inch of the top only; it will burn one hour. The hottest part of the flame is not down close to the wick, as most beginners suppose, but up just beneath the tip.

FIG. 5

THE LAMP

Buy your alcohol at a drug store in quantities of one pint or more. When you are through experimenting for the day pour the alcohol from the lamp back into the pint bottle and cork the bottle tightly. Alcohol left in the lamp gradually evaporates and is lost.

Do not let the lamp stand with alcohol in it for any considerable time—overnight for example—because fuel alcohol contains water and when it evaporates from the wick, the alcohol evaporates first and leaves the water in the wick. Then when you try to light the wick again, you will find that you cannot do so, because, of course, water does not burn. If this happens to you, take the wick out, dry it, and start the lamp again.

FIG. 6

MAKING A SCRATCH

It is perfectly safe to use kerosene in the lamp, but it gives a very smoky flame which deposits soot on the glass and fills the air with soot particles. Your mother will object very strenuously to this because the soot particles settle and blacken everything. Burn alcohol only, at least in the house.

Experiment 2. To cut glass tubing.

FIG. 7

BREAKING THE TUBE

Cut off a six-inch length of No. 2 as follows: Lay the tube flat on the table, mark the six-inch length and draw the file across the tube at this point, pressing hard enough to make a good scratch (Fig. 6). Grasp the tube with both hands near the scratch, as in Fig. 7, pull apart and bend slightly. Do you find that the tube breaks across easily?

Repeat this with No. 4 and No. 6 tubes.

Experiment 3. To make the edges smooth.

FIG. 8

MAKING THE EDGES SMOOTH

Hold one end of the six-inch piece of No. 2 in the tip of the flame (Fig. 8), and turn constantly until it is just red hot. Take it out and let it cool on the blocks. Do you find that the edges are smooth?

Repeat with the other end.

Repeat with both ends of the six-inch piece of No. 4.

If thick glass is heated quickly it may crack, because the hot exterior expands more quickly than the cooler interior and produces internal strains.

FIG. 9

THE BLOWPIPE FLAME

The No. 6 tube is comparatively thick and should be heated gradually as follows: Hold the end in the flame for about 1 second, then withdraw it for about 1 second; hold it in the flame again for 1 second, and withdraw it for 1 second. Repeat this eight or ten times, then hold and turn it in the flame until red hot.

Smooth both ends of the No. 6 piece in this way.

Experiment 4. Practice with the blowpipe.

Hold the small end of the blowpipe just inside the flame at one edge, about ⅛ inch above the wick (Fig. 9), and blow air through the flame parallel to the top of the wick.

Keep your mouth closed on the blowpipe, breathe through your nose, and practice keeping a steady stream of air going for a long time. You will be able to do this with a little practice.

Do you observe that the blowpipe flame is pointed, also that it is made up of a pointed cone inside and a lighter-colored cone outside? The hottest part of the flame is inside the outer cone just beyond the point of the inner cone.

FIG. 10

CLOSING ONE END OF A TUBE

The blowpipe flame is hotter than the lamp flame because the heat of the burning alcohol is concentrated at one point by means of the air blast, and because the alcohol is more completely burned by the extra air.

Experiment 5. To close the end of a small tube.

Hold one end of a piece of No. 2 tube in the blowpipe flame (Fig. 10), turn it slowly, and heat until the end closes. Does it close nicely?

Close one end of a piece of No. 4 in the same way.

You can close No. 6 tubing in this way, but it leaves a large lump of glass which may crack on cooling or on reheating. You will practice closing No. 6 tubing later.

The “why” of it

The glass becomes soft when heated because it becomes almost a liquid, and if it is heated sufficiently it becomes entirely a liquid. In this respect it acts very much as pitch, rosin, and wax act when heated by the sun or by a fire.

FIG. 11

MAKING A GLASS BUBBLE

The end of a glass tube becomes smooth, or closes entirely, when heated, for the following reason: The surface of any liquid tries to take the smallest possible area (this is explained in detail under “Surface Tension” in the Gilbert book on “Experimental Mechanics”), for example, a small particle of water takes the shape of a drop, a sphere, and the surface of a sphere has the least area for a given amount of water. Now when the end of the glass tube is heated it becomes a liquid, and the surface of this liquid contracts the glass into a smooth rounded surface of least area. If the tube is heated still more, the surface contracts still more and closes the end.

Experiment 6. Fun blowing glass bubbles.

Smooth one end of a piece of No. 2 tube and allow it to cool. Close the other end in the blowpipe flame, turn it slowly, and heat until it is very hot. Take the tube out of the flame, put the smooth end into your mouth quickly, and blow as hard as you can (Fig. 11). Do you get a fine big glass bubble which bursts with a pop?

If you get only a small bulb at the first trial, heat the end, and try again. Do you find that the bulb shrinks when heated but blows out again readily?

FIG. 12

BLOWING A BULB

When you get a big bubble, place the bubble end of the tube on a cooling block and break all the thin glass away from the tube by striking it with the file or blowpipe. Then close the end and blow another bubble.

Repeat until you can blow bubbles easily.

Repeat with a piece of No. 4 tube.

BUBBLE COLORS

FIG. 13

A WATER BALLOON

Do you find that the thin glass of the bubbles shows colors, especially in sunlight, just as soap bubbles do? You boys who have had the Gilbert set on “Light Experiments” will know that these colors are due to “interference.” The colors produced by a thin film of oil on water are also produced by “interference.”

Experiment 7. To make water balloons.

Close one end of the No. 2 tube in the blowpipe flame again and while it is still hot blow carefully into the open end until you have a bulb about ½ inch in diameter (Fig. 12). Now let it cool. Make a scratch with the file about ¼ inch from the bulb, break the tube at this point (Fig. 13), and smooth the rough edge.

FIG. 14

THE BALLOON SINKS AND RISES

Put the bulb in a tumbler of water. Does it float? If not, make another balloon with a larger bulb.

Experiment 8. Magic.

Find a large bottle made of clear glass, the neck of which will fit your solid rubber stopper.

Fill the bottle with water to overflowing, insert the balloon, and then the stopper.

Now press down hard on the stopper. Does the balloon sink in a most magical manner (Fig. 14)?

Release the stopper. Does the balloon rise in an equally magical manner?

FIG. 15

A BALLOON RACE

Experiment 9. Balloon races.

Make another water balloon. Put the two balloons together in the bottle filled to overflowing with water.

Insert the stopper and press down hard. Do the balloons sink (Fig. 15), and does one sink more quickly than the other?

Release the stopper. Do the balloons rise, and does one rise more quickly than the other?

The most buoyant balloon sinks last and rises first.

The “why” of it

FIG. 16

DRAWING A THIN TUBE

You boys who have the Gilbert set on “Hydraulic and Pneumatic Engineering” will know the “why” of the last three experiments. Any body floats in water if it is lighter than an equal volume of water, and it sinks if it is heavier than an equal volume of water. Water is practically incompressible but air is very compressible: thus when you press down on the stopper, you force water into the balloon and compress the air in it; when you release the stopper, the compressed air in the balloon expands and drives the water out. When the weight of the balloon and the weight of the water in it are together greater than the weight of water displaced by the balloon, the balloon sinks; when they are less, it rises.

Experiment 10. Fun with thin tubes.

Hold a piece of No. 2 tubing in the lamp flame and turn it constantly. When it is red hot and soft, take it out of the flame and pull your hands apart until the tube is stretched ten or twelve inches (Fig. 16). Is the tube in the shape shown in Fig. 17?

FIG. 17

A GLASS TUBE STRETCHED

Allow the tube to cool, break the large ends away from the thin tube, place one end of the thin tube in a glass of water, and blow into the other end to make air bubbles in the water (Fig. 18). If you can do so, it is a real tube.

FIG. 18

AIR THROUGH TUBE

Does the thin tube bend easily and does it spring back when released?

Repeat the experiment with another piece of No. 2 tubing, but make the thin tube as long as you can.

Can you blow air through the thin tube, and does it bend very easily indeed?

Repeat with a piece of No. 4 tubing.

These thin hairlike tubes are called “capillary” tubes, from the Latin word capillus, meaning a hair.

Experiment 11. Magic.

FIG. 19

WATER RUNS UPHILL

You have always heard that water runs downhill, but you will now see it run uphill and remain there in a most magical manner.

Cut off 5-inch lengths of No. 6, No. 4, and No. 2 tubing, stand them side by side in a glass full of water (Fig. 19), and move them up and down in the water to wet the inside of the tubes.

Now look at the water level in each of the tubes. Is it above the level of the water in the glass, and is it higher the smaller the inside diameter of the tube, that is, is it higher in the No. 2 than in No. 4, and in No. 4 than in No. 6?

Now take the thin capillary tube which has the largest inside diameter, place one end in the glass of water, suck it full of water and blow it out. Now with one end in the glass of water notice quickly how the water rises inside the tube. Does it run uphill in a most magical manner (Fig. 20), and does it remain there?

FIG. 20

WATER RUNS UP TUBE

Repeat this with your other capillary tubes. Does the water run uphill in each, and does it rise higher the smaller the inside diameter of the tube?

The “why” of this is explained in Gilbert’s “Experimental Mechanics” under “Capillarity.”

WHAT IS GLASS?

Common glass is made from three substances with which you are all more or less familiar; namely, sand, sodium carbonate (washing soda), and lime.

If sand and soda or potash are mixed and heated to a high temperature, they melt together and produce a glass which dissolves in water. This is known as “water glass” and it is used in many ways: to preserve eggs, to cement fire bricks, to make fireproof cement, and so on. If, however, lime is added and the mixture is heated to a high temperature, a glass is produced which is not soluble in water. This is the glass you know.

The three most common kinds of glass are: Venetian glass, made from sand, soda, and lime; Bohemian glass, from sand, potash, and lime; and crystal or flint glass, from sand, potash, and lead oxide.

FIG. 21

SECOND STEP IN MAKING WINDOW PANES

FIG. 22

IRONING THE CYLINDERS FLAT

HOW ARE THINGS MADE OF GLASS?

The glass mixture is heated to a high temperature in fire clay pots or tanks in large ovens. The surface is skimmed from time to time and the heating is continued until all air bubbles have escaped from the mixture, usually about three days.

The glass is now quite fluid and it is allowed to cool somewhat until it is viscous; then the objects are made by blowing, pressing, or rolling, as described below.

The finished articles are finally “annealed,” that is, they are placed while still hot in a second hot oven, which is then sealed and allowed to cool slowly, for four or five days or for as many weeks, according to the kind of glass.

If a glass object cools quickly, it cools more rapidly on the surface than in the interior. This produces a condition of strain in the glass and the object may drop to pieces when jarred or scratched. This condition of strain is avoided by allowing the objects to cool very slowly, that is, by annealing.

WINDOW GLASS

Window glass is blown in exactly the same way as you have blown glass balloons; the process is illustrated in Fig. 1.

The glass mixture is heated for about three days in fire clay pots and is allowed to cool until it is viscous. The glass blower then attaches a lump of the viscous glass to the end of a straight iron blowpipe about five feet long and blows a bulb. He then reheats the glass and blows a larger pear-shaped bulb and in doing so rests the glass on a pear-shaped mold of charred wood (see center of Fig. 1). He again reheats the glass, holds the pear-shaped bulb over a pit, and blows a long cylinder (see left of Fig. 1).

The ends of the cylinder are now cut off and the edges are smeared with molten glass to prevent splitting (see right, Fig. 21). The cylinder is next cut lengthwise with a diamond (center, Fig. 21), and is placed in a second hot oven, where it is ironed out flat (Fig. 22).

FIG. 23

BOTTLES BLOWN IN A MOLD

The flat sheets are finally annealed in a third oven for a number of days and are then cut into panes, sorted, and packed.

GLASS TUBES

FIG. 24

ROLLING PLATE GLASS

The glass tubes with which you do the experiments in this book are made in the same way as window glass up to the stage of blowing the cylinder; then the blower’s helper attaches an iron rod to the opposite end of the cylinder (see right of Fig. 1), and the blower and helper walk backward away from each other to pull the cylinder into a tube. Of course, they use a small amount of glass to make small tubes, and larger amounts for large tubes.

MOLDED GLASS

Many articles of glass are made by blowing the glass in molds. Bottles are made in this way (Fig. 23), and large machines are now in use which mold many bottles at one time in this way.

PRESSED GLASS

Many articles are made by pressing glass into molds, that is, the molten glass is poured into molds and is pressed against the sides of the mold by means of a plunger. Imitation cut glass is pressed in this way.

PLATE GLASS

The large sheets of plate glass used in store windows are not blown, but rolled. The molten glass is poured from the fire clay pots upon a cast-iron table and is rolled flat by means of a large iron roller (Fig. 24). The glass is then in the shape of plate glass, but is rough on both sides. It is annealed for a number of days and then is ground smooth on both sides, first with coarse emery, then with finer and finer emery, and is finally polished with rouge. The result is the beautifully polished plate glass we see in large windows.

OPTICAL GLASS

The United States and Great Britain made great strides in the manufacture of optical glass during the war and there are now many kinds on the market. They are used in making the lenses, prisms, and mirrors for optical instruments.

Optical glass is made in much the same way as ordinary glass, but great care is taken: first, to see that the materials are pure; second, to stir the glass constantly, as it cools from the molten to the viscous state, to make it as uniform as possible; and third, to cool it very slowly in the annealing process, to avoid strains.

QUARTZ GLASS

FIG. 25

A POLLYWOG

An entirely new glass has been placed on the market in quantity in recent years. It is made by melting very pure quartz sand at a temperature of 3000° F. and cooling it fairly rapidly. It has the very valuable property of expanding and contracting very, very slightly when heated and cooled. Thus there is practically no internal strain set up when it is heated or cooled quickly and it does not break. It can be heated red hot, for example, and then plunged into cold water without breaking. It is probable that this glass will be in universal use in a very few years.

Experiment 12. To make an acrobatic pollywog.

Smooth one end of a piece of No. 2 tube to put in your mouth, close the other end in the blowpipe flame, take it out and blow a bulb about ½ inch in diameter.

Allow the bulb to cool, then heat the tube about ¼ inch from the bulb and draw it out into a thin tube. Now bend the thin tube at right angles near the bulb and break it off (Fig. 25).

Place the bulb in water. Does it float? If not, blow another with a larger bulb.

Experiment 13. Magic.

FIG. 26

ACROBATS

Place the pollywog in a bottle filled to overflowing with water, insert the solid rubber stopper, and press it down hard. Does the pollywog sink?

Now release the stopper quickly. Does the pollywog turn somersaults in a most magical manner (1, Fig. 26), and also rise?

Make one or two more pollywogs, place them all in the bottle together (2, Fig. 26), and entertain your friends with a pollywog circus.

The pollywog sinks when you press down on the stopper because you compress the air in it and force water in until it weighs more than the water it displaces.

FIG. 27

DANCING POLLYWOGS

The pollywog rises when you release the stopper because the compressed air drives the water out until the pollywog weighs less than the water it displaces.

The pollywog turns a somersault because the water rushes out sidewise in one direction and forces the nozzle in the other direction.

Air may escape from the pollywog when it is turning a somersault; if so, water will take its place, and may make the pollywog too heavy to float. You can restore its buoyancy by sucking out the water.

Experiment 14. A dancing pollywog.

FIG. 28

DRAWING GLASS SPIDER-WEBS

Make a pollywog as in Experiment 12, but bend its tail twice as shown in 1, Fig. 27; the nozzle is at one side and points sidewise.

FIG. 29

THE SPIDER TRICK

Put it in the bottle full of water, then press down and release the stopper. Does it sink and rise, and does it also whirl around most beautifully as it rises?

Make another pollywog (2, Fig. 27), but bend its nozzle in the opposite direction. Does it whirl in a direction opposite to that of the first pollywog?

Put them in the bottle together and treat your friends to a pollywog dance.

The pollywog whirls because the water rushes out of the nozzle in one direction and forces the nozzle in the opposite direction.

Experiment 15. To make glass spider-web.

Heat the end of a piece of No. 2 tube in the blowpipe flame until it is melted and very hot. Now touch the end of another piece of glass to the melted glass, remove from the flame, and quickly pull the two pieces apart as far as you can (Fig. 28). Do you find that you have pulled part of the melted glass out into a very fine glass spider-web?

Repeat, but ask a friend to touch the second piece of glass to the first and run away as fast as he can.

Do you get a much finer spider-web?

Is the glass spider-web fairly strong and very flexible?

Experiment 16. The ancient spider trick.

FIG. 30

ATTACHING A HANDLE

Attach an imitation spider—or the dead body of a real spider—to the end of the glass spider-web and surprise your friends, as shown in Fig. 29. The glass spider-web is much less visible than a thread for this purpose.

Experiment 17. To make working handles.

You can save glass in many cases by attaching a short piece of glass to the piece you intend to work with, as follows: Heat an end of each piece in the lamp flame until red hot, press them together, remove from the flame, and hold until solid. The short piece then serves as a working handle (Fig. 30) for the large piece.

Experiment 18. To close a large tube.

You closed small tubes in Experiment 5 by simply heating the end in the blowpipe flame. This method does not serve for large tubes, however, because it leaves a very large lump of glass which may crack on cooling or reheating.

FIG. 31

CLOSING A LARGE TUBE

FIG. 32

MAKING A SUBMARINE

Practice the following method of closing a large tube; first with a piece of No. 4 tube, and then with a piece of No. 6: Attach a working handle to the end to be closed, heat the tube ½ inch from the end in the blowpipe flame, turn constantly, and when soft pull apart until the tube has the shape 1, Fig. 31. Heat, turn, and pull the end away to leave the tube as in 2. Heat the end and blow out until it has the shape 3. The end is now closed and the glass has about the same thickness as the remainder of the tube.

Experiment 19. To make a submarine.

Close one end of a piece of No. 2 tubing as described above, but leave the end somewhat pointed (1, Fig. 32). Heat the tube on one side at a distance ½ inch from the end and blow a bulb about ½ inch in diameter (2). Heat the tube ¼ inch from the bulb, draw it down into a fine tube, and break off the tube, leaving a small hole in the end (3). Place the submarine in a glass of water, and if it floats it is complete.

Experiment 20. Magic.

FIG. 33

THE SUBMARINE SUBMERGES

Fill a bottle to overflowing with water, insert the submarine open end down, insert the solid rubber stopper and press down hard (Fig. 33). Does the submarine submerge?

Release the stopper. Does the submarine rise and does it also move forward?

Turn the bottle on its side and release the stopper quickly. Does the submarine shoot forward at a great rate (Fig. 34)?

The submarine acts in this magical manner for the reasons given in Experiment 9. When you press the stopper in, you compress the air in the submarine and force water in until the submarine weighs more than an equal volume of water and it sinks. When you release the pressure on the stopper, the compressed air forces the water out until the submarine becomes lighter than an equal volume of water and it rises. The water rushing out through the opening exerts pressure backward on the water in the bottle and the reaction drives the submarine forward.

Experiment 21. Fun with the submarine.

If your friends do not know about the little submarine, you can mystify them as follows: Tell them that submarines are just like other fish; namely, they lay eggs, and the little eggs hatch out after a certain number of days (of course, your friends will know that you are only joking). Pretend that you found one of these submarine eggs, hatched it out in lukewarm water, and that you have trained the baby submarine to do some simple tricks. For example, that you have trained it to submerge, rise, and attack, when you issue the commands “submerge,” “rise,” and “attack.”

FIG. 34

THE SUBMARINE SHOOTS FORWARD

Tell them to watch the submarine carefully and to notice that it takes in water and submerges when you issue the command “submerge.” Stand the bottle on the table, issue the command “submerge” and, while your friends are watching the submarine, press down on the stopper unknown to them.

FIG. 35

A SUBMARINE BATTLE

Tell them to watch the submarine carefully again and to notice that it expels water and rises when you issue the command “rise.” Issue the command and unknown to them release the pressure on the stopper slowly.

Repeat with the command “attack” and release the pressure quickly.

Experiment 22. A submarine battle.

Make a second submarine, place it in a large bottle with the first submarine, turn the bottle on its side, and make the submarines manœuver by moving the stopper in and out.

FIG. 36

FLARING A TUBE

Finally arrange them so that they are on the bottom, facing each other bow to bow, two or three inches apart (1, Fig. 35), and release the stopper quickly. Do the submarines try to ram each other (2, Fig. 35) in a most realistic manner?

FIG. 37

AN AIR GUN

Experiment 23. To flare the end of a tube.

Heat the end of a piece of No. 2 tube until it is red hot, take it out of the flame, hold the flaring wire inside the end, and press outward gently while you revolve the tube (1, Fig. 36). Do you find that the end is flared out (2, Fig. 36)?

Experiment 24. To make an air gun.

Take a full length piece of No. 4 tube and flare both ends slightly. This is the air gun (Fig. 37).

Now to make an arrow, cut off the lighting end of a match and insert a pin in the other end (Fig. 38).

FIG. 38

THE ARROW IS SHOT PIN-END FIRST

Insert this arrow in the air gun and blow it out. Does it come out with considerable speed?

Experiment 25. A shooting match.

FIG. 39

A SHOOTING MATCH

Draw a target on a piece of paper and hang it up, away from the wall or at the edge of the table, where there will be space behind for the arrows to pass through. Now shoot at the target with your air gun (Fig. 39). Do you find that the arrow makes holes in the target and sometimes goes right through?

The bull’s-eye of a target is usually 1 inch in diameter, the next circle outside is 2 inches in diameter, the next 4 inches, and the outer circle 5 inches.

Get up a shooting match and keep track of the score made by each.

If the bull’s-eye is cut anywhere by the arrow, the count is 5 points; a cut anywhere inside or touching the 2-inch circle counts 4 points; anywhere inside or touching the next two circles counts 3 and 2 points respectively.

The one who makes the highest score in five shots is the winner.

It is more sanitary if each shooter has his own air gun and arrows.

Experiment 26. Height and distance contest.

Go outside and see which of you can shoot his arrow to the greatest height and to the greatest distance.

Give each contestant five shots.

FIG. 40

THE PEA SHOOTER IN ACTION

You can make fair estimates of the heights if you shoot up beside a building or tall tree.

Experiment 27. To make a pea shooter.

FIG. 41

BENDS

Take a full length piece of No. 6 tubing, smooth both ends and flare them out slightly. This makes an excellent pea shooter. Try it with peas. Do you find that they come out with great speed?

Experiment 28. A pea-shooting match.

Make a target on a piece of paper, hang it up away from the wall or at the edge of the table, and shoot at it (Fig. 40). Do you find that the peas go right through the paper?

Arrange a match with your friends and keep track of the score as in Experiment 25.

Experiment 29. To make a good bend.

A good bend has the same diameter in the bend as in the remainder of the tube (1, Fig. 41). It is rather difficult to make because the tube tends to cave in on the inside of the bend (2) or flatten on the outside (3), or both.

FIG. 42

A DRINKING TUBE

Make the bend as follows: Heat a piece of No. 2 tube about 2 inches from one end in the lamp flame, turn it constantly and move it back and forth endwise to heat a length of about 2½ inches. When soft, take the tube out of the flame, and bend the ends upward until the angle is 90°.

If the bend is flat on the inside or outside, close one end of the tube in the blowpipe flame, smooth the other end and allow them to cool, then heat the flat side of the bend in the blowpipe flame and blow it out slightly. This makes the diameter of the tube at the bend equal to that of the remainder of the tube. Cut off the closed end, smooth the edge, and your bend is complete.

Make bends with No. 4 tube.

FIG. 43

A SIPHON

Experiment 30. To make a drinking tube.

Many times when there is sickness in the house, it is convenient to have a glass drinking tube (Fig. 42), through which the patient can drink without raising his head.

Make such a tube from a piece of No. 4 tubing. The short arm is equal in length to the depth of the tumbler; the long arm, or mouthpiece, is about 1 inch longer than this.

Experiment 31. To make a siphon.

Cut off a piece of No 4 tubing 8 inches long, make two right-angled bends about 1 inch apart at the center, smooth both ends, and your siphon is complete (Fig. 43).

FIG. 44

A SIPHON

Experiment 32. Magic.

Put one arm of the siphon in a tumbler of water and suck air out of the other end. Does the water start running and does it continue to run in a most magical way (Fig. 44) until the water is below the end of the siphon in the tumbler?

FIG. 45

FROM THE HIGH LEVEL TO THE LOW

Fill the tumbler with water again, start the water running, put the outer arm of the siphon in an empty tumbler, and stand both tumblers on the table (Fig. 45). Does the water run up one arm of the siphon and down the other into the empty tumbler? Does it stop running when the levels are the same?

Stand the first tumbler on a book. Does the water run again and stop when the levels are again the same (Fig. 46)?

Place the lower tumbler on the book and the upper tumbler on the table. Does the water now run in the opposite direction until the levels are again the same?

Raise one tumbler a foot or so above the table. Does the water run up over the edge and drop into the second? Now before the upper tumbler is empty, lower it in such a way that an arm of the siphon is in each tumbler, and raise the second tumbler. Does the water now run in the opposite direction?

FIG. 46

THE WATER STOPS WHEN LEVELS ARE THE SAME

You boys who have the Gilbert set on “Hydraulic and Pneumatic Engineering” will know that it is the pressure of the atmosphere which causes the water to run up over the edge of the tumbler in this magical way.

Experiment 33. A long-armed siphon.

FIG. 47

SIPHONING WITH LONG TUBES

Attach a full length of No. 4 tube to each arm of the siphon, as in Fig. 47, and repeat the experiments described above.

Note: When you insert a glass tube into a rubber coupling or rubber stopper, wet the end of the glass tube and the inside of the coupling or stopper, grasp the tube near the end to be inserted, and insert with a twisting motion.

Experiment 34. To make a nozzle.

Attach a working handle to one end of a piece of No. 2 tube, heat the tube about one inch from the end in the lamp flame, turn constantly until soft, then remove from the flame, and draw it out about 3 inches. When cool, break off the thin tube, cut off the nozzle to a length of about 2½ inches, smooth the large end, and your nozzle (Fig. 48) is complete.

Experiment 35. To make a fountain.

Arrange the apparatus as in Fig. 49, and suck air out of the nozzle. Have you made a beautiful fountain?

FIG. 48

A NOZZLE

YOU MAKE A NUMBER OF MAGIC FOUNTAINS

Experiment 36. Magic.

Make a nozzle 6 inches long out of No. 2 tube. Smooth the ends of the nozzle, and long tubes. Arrange the apparatus as in Fig. 50 and suck air out of the nozzle until the water runs in the siphon. Does the water squirt out of the nozzle in a magical manner?

Experiment 37. More magic.

Arrange the No. 2 apparatus as in Fig. 51, with the nozzle inside the bottle. Now to start the apparatus: Fill the bottle about quarter full of water, insert the tubes in the stopper as shown; insert the stopper into the mouth of the bottle; invert the bottle; then put the short tube in a tumbler full of water and the long tube in an empty pail or basin. Is there a magical fountain inside the bottle?

Repeat this with a taller bottle, if you can find one to fit your two-hole stopper. Do you get a higher fountain?

Experiment 38. Still more magic.

FIG. 53

STARTING A SIPHON

Make another nozzle and attach it to the apparatus used in the last experiment by means of the inverted siphon (Fig. 52). Start the experiment as described above. Do you get two fountains?

Experiment 39. To start a siphon.

FIG. 54

SIPHONING SAND

You can start a siphon without sucking the air out of it as follows: Fill the siphon with water, put a finger over each end (1, Fig. 53), place one end in a tumbler full of water and remove the finger under water (2, Fig. 53), then remove the other finger. Does the siphon start?

In this case the water you pour into the siphon drives the air out, and this is the reason you do not need to suck the air out.

Experiment 40. To siphon sand or mud.

Arrange a siphon (Fig. 54), start the water flowing, and then pour sand or mud into the upper tumbler. Is the sand of mud siphoned over into the lower tumbler?

FIG. 55

A SQUIRT BOTTLE

Attach a long tube to the outer arm of the siphon and repeat the experiment. Is the sand or mud siphoned more rapidly and more thoroughly?

Experiment 41. To make a squirt bottle.

FIG. 56

SQUIRT BOTTLE IN ACTION

Make a nozzle at one end of a piece of No. 2 tubing, make a bend near the nozzle, cut off the other end at such a length that it will reach to within ¼ inch of the bottom of the bottle, smooth this end, allow it to cool, wet the tube and the two-hole stopper, shove it through one hole of the stopper, insert an elbow in the other hole, and your squirt bottle is complete (Fig. 55).

Fill the bottle with water, and blow through the elbow. Do you get a fine long stream from the nozzle (Fig. 56)?

FIG. 57

TUBE FOR TRICK SQUIRT BOTTLE

Experiment 42. To make a trick squirt bottle.

You can have any amount of fun with a trick squirt bottle. It is exactly the same as the squirt bottle described in Experiment 41 except that it has a hole just below the bend (Fig. 57).

FIG. 58

MAKING A SMALL HOLE

To make the hole, make the long bent nozzle as in the last experiment, then heat the tube just below the bend in the blowpipe flame, touch a piece of glass tube to the red-hot glass (1, Fig. 58), and pull it away (2, Fig. 58). Do you find that the hot glass is pulled out into a thin pointed tube? Break off the thin tube close to the large tube, heat in the blowpipe flame until the edges are smooth and at the same level as the sides of the large tube. Flare the edges of the hole, if necessary; it should be about ⅛ inch in diameter.

FIG. 59

TRICK SQUIRT BOTTLE

Now fill the bottle with water, and blow hard (Fig. 59). Do you find that one stream of water is driven into your face and another out of the nozzle?

Experiment 43. Fun with a trick squirt bottle.

FIG. 60

TRICK BOTTLE IN ACTION

Now to have fun with your trick bottle, show it to one friend at a time. Do not ask him to try the bottle, just go where he can see you and squirt a long stream, but unknown to him have your finger over the hole below the bend.

FIG. 61

A SIMPLE ENGINEER’S LEVEL
(From Aldous’ Physics. Courtesy of The Macmillan Company)

Your friend will just naturally want to have a try at it. So you say “All right, let’s see who can squirt the longest stream.” Tell him that all he has to do is to take a deep breath and blow as hard as he can. He will do so, with laughable results (Fig. 60).

Now together find another friend. Do not ask him to blow, but each of you blow as long a stream as you can, where he can see you. He will beg to be allowed to try, and finally you let him, with the same laughable results.

FIG. 62

ONE-LEGGED TABLE AND LEVEL

Repeat with other friends.

Experiment 44. To make an engineer’s level.

You can make one form of engineer’s level (Fig. 61) as follows: Take a full length of No. 6 tubing, bend it up 4 inches at each end, smooth the ends, attach it to a small board, rest the board on a one-legged table, and you have a serviceable level (Fig. 62).

Fill the tube with water, shove the pointed end of the leg into the ground and sight along the outside of the upright tubes at the level of the water surfaces. The line along which you sight is exactly horizontal, because the water surfaces are at exactly the same level.

Experiment 45. To use the engineer’s level.

FIG. 63

HOMEMADE LEVEL IN USE

An engineer’s level is used to find the difference in level of two or more points (Fig. 63).

To practice using your level, find the difference in level of two points 100 feet apart on a road, sidewalk, or railroad.

To do this, you must first make what is called a leveling rod. Find a piece of wood about one or two inches square and six or more feet long, mark on it feet and inches, beginning at the bottom end, and your leveling rod is complete.

Now to find the difference in level of two points 100 feet apart, scratch a line or insert a small stake at one point, then pace off 100 feet and mark the second point. Now set up your level between the two points, ask a friend to hold the rod on the ground and upright, at the first point, sight along the water levels at the rod, and ask your friend to move his finger, or a white card, up and down until it is exactly in your line of sight. Now ask your friend to tell you exactly where his finger or card is and record this height. Let us suppose that it is 4 feet 6 inches above the ground. Now leave the level exactly where it is, ask your friend to hold the rod upright at the second point, and again sight along the water levels at the rod. Let us suppose that his finger or card is now exactly 3 feet above the ground.

The difference in level at the two points is 4 feet 6 inches minus 3 feet or 1 foot 6 inches. That is, the second point is 1½ feet above the first point or the grade is 1.5 feet in 100, or 1.5 per cent.

You can now mark a third point 100 feet beyond the second point, set up your level between the second point and third point, place the rod at the second point, then at the third point, and find their difference in level as above. If the third point is 1 foot above the second, the total rise in the 200 feet is 2½ feet; if, however, it is 1 foot below the second, the rise is 1½ minus 1 or ½ foot in the 200 feet.

You can repeat this with as many points as you please.

FIG. 64

A SPIRIT LEVEL

Experiment 46. To make a spirit level.

The spirit level (Fig. 64) is simply a curved glass tube filled with alcohol except for the bubble and closed at both ends. The curve of the tube is part of a circle.

FIG. 65

MAKING A SPIRIT LEVEL

Make a spirit level as follows: Take a piece of No. 4 tube about 7 inches long, heat a space about 3 inches long in the lamp flame, turn constantly, and when soft remove from the flame, hold both ends and allow the center to sink into a slight curve (1, Fig. 65).

Let the tube cool, mark the center of the curve with ink, and make marks 2 inches from the center on each side.

Hold the tube crosswise in the lamp flame, heat at one mark, draw down the tube and close it (2).

In a similar manner draw down the tube at the other mark but do not close it (3).

Let the tube cool and fill it with alcohol to the level shown in 4. To do this easily make the pipette (5), suck alcohol into it within about 1 inch of the top, put your finger over the top, insert the lower end of the pipette to the bottom of 4, and remove your finger.

FIG. 66

MOUNTING THE SPIRIT LEVEL

Heat the small part of 4, without heating the alcohol, and close the tube (6). Now attach the level to a smooth board as 2 or 3, Fig. 66, mark the center of the bubble, and your spirit level is ready for use.

Experiment 47. To make a fountain-pen filler.

Attach a rubber coupling to the large end of one of your No. 4 nozzles, close the other end of the coupling with a glass plug, and your fountain-pen filler is made (Fig. 67).

To make the plug, close one end of a piece of No. 4 tubing, allow it to cool, cut off to a length of 1 inch and smooth the rough edges. Insert the closed end of this plug into the rubber coupling.

Practice using the filler by drawing up and shooting out water.

FIG. 67

A FOUNTAIN-PEN FILLER

Experiment 48. To make a syringe.

Take a half length of No. 6 tube and smooth both ends in the lamp flame or blowpipe flame.

Now to make a plunger: Cut an 8½-inch length of No. 2. smooth one end, close the other end and blow a slight bulb. When cold, wet the closed end and insert it into a small wet rubber coupling.

Note: Always grasp a tube near the end when you insert it into a coupling or stopper, because if you hold it too far back you may break it. Insert it with a twisting motion, after wetting the end and the inside of the coupling or stopper.

FIG. 68

A SYRINGE

Wet the inside of the large tube, wet the plunger and rub it on a cake of soap to make it slippery, then try it in the large tube. If the plunger is too large, stretch the coupling lengthwise; if it is too small, crowd the coupling together lengthwise. If the bulb is too large or too small, dry it, heat in the blowpipe flame until it shrinks, and blow another.

When the plunger is made, attach a No. 4 nozzle to the No. 6 tube with a large coupling, arrange as in Fig. 68, and your syringe is made.

Fill the large tube with water and see how long a stream you can make.

FIG. 69

ANOTHER SYRINGE

Experiment 49. To make another syringe.

Heat a piece of No. 6 in the blowpipe flame at a length of 7½ inches and draw it out into a nozzle; smooth the other end in the lamp flame. Use the same plunger as in Experiment 48, and your syringe is made (Fig. 69). Try it out with water.

Experiment 50. To make a third syringe.

Heat a piece of No. 6 tube in the blowpipe flame at a length of 7½ inches, draw it out, and close the end, then smooth the other end.

Now to make a plunger: Heat a piece of No. 2 tube 8½ inches from one end in the lamp flame, draw it out into a nozzle, and break it off, leaving a small hole at the end of the nozzle. Smooth the other end in the lamp flame, flare it out slightly, allow it to cool, dip it into water and insert it into a small wet coupling.

FIG. 70

A THIRD SYRINGE

Now fill the large tube with water and insert the coupling plunger (Fig. 70). Do you get a fine long stream?

Experiment 51. To make a diablo whistle.

Use the No. 6 tube and the No. 2 plunger from Experiment 48, arrange as in Fig. 71, blow across the top, and move the plunger up and down. Do you get a most diabolical sound?

FIG. 71

THE DIABLO WHISTLE

The sound is produced by the vibration of the air column between the top of the tube and the top of the plunger. Do you find that the pitch of the note is higher the shorter the air column?

Experiment 52. Fun with the diablo whistle.

Start with the air column long and blow the note, shorten it a little and blow the next note, continue, and try to blow the eight notes of an octave.

FIG. 72

JOINING TWO TUBES

Try to play a tune.

Try to make the most weird sound you can.

Experiment 53. To join two tubes end to end.

Take a piece of No. 2 tube about 7 inches long, close one end, smooth the other, and when cool cut the tube at the middle.

FIG. 73

WORKING THE JOINT

Now join these two pieces as follows: Hold the ends opposite each other near the top of the lamp flame (Fig. 72), rotate constantly, and when nearly red hot bring the ends accurately together in the flame, press together slightly, draw out slightly, and remove from the flame.

The ends are now stuck together, but the glass is in a slight lump around the joint and if allowed to cool will crack very easily. It is necessary to work the glass back and forth to get rid of the lump and to make the glass uniform on both sides of the joint. Do this as follows: Heat one third of the joint in the blowpipe flame (Fig. 73), and when red hot blow a slight bulge. Now turn the joint one third, heat the next third red hot and blow a slight bulge. Repeat with the remaining third.

FIG. 74

JOINING TUBES OF DIFFERENT SIZES

Now heat the first third again until it is red hot and shrinks, then blow a slight bulge again. Repeat this with the other two thirds.

Repeat this whole operation a third time and blow just enough to leave the joint the same size as the remainder of the tube or a little larger.

FIG. 75

MAKING A LARGE HOLE

This heating and blowing has worked the joint back and forth until the glass is fairly uniform. It makes a strong joint.

Cut off the closed end and smooth the edge.

Repeat with a piece of No. 4 tube.

FIG. 76

MAKING A TEE

Experiment 54. To join tubes of different sizes.

Take a piece of No. 4 tubing about 3 inches long and close one end.

FIG. 77

THREE-ARMED SIPHON

Take a piece of No. 6 tubing, attach a handle to one end, heat the No. 6 tube in the blowpipe flame about 1 inch from this end and draw it down to smaller size.

Break the small part at a point where it is about the size of the No. 4 tube. If the hole is too large, heat the edge until it is a little too small and flare it out with the flaring tool. If the hole is too small, heat the edge and flare it out.

Now heat the ends of both tubes (Fig. 74), and join them as described in the last experiment.

Repeat the operation of heating and blowing at least three times.

Join a No. 4 and a No. 2 tube in the same way.

Experiment 55. To make a large hole.

Take a piece of No. 4 tube about 6 inches long, close one end, smooth the other, and allow it to cool.

FIG. 78

A REPEATING AIR GUN

Now to make a large hole in the side of this tube, proceed as follows: Heat in the blowpipe flame the point at which you wish to make the hole, and blow a slight bulge (1, Fig. 75). Then heat the top of this bulge until it is red hot over an area about equal to the size of the hole you wish to make, and blow hard to make a thin bubble (2, Fig. 75). Break away the thin glass of the bubble, smooth the edges, and the hole is made. The edge of this hole will project beyond the side of the tube (3, Fig. 75). If you wish to make the edge even with the side of the tube, heat it in the blowpipe flame until it shrinks back level with the tube.

FIG. 79

FOUR-WAY JUNCTION

Experiment 56. To make a tee.

Take a piece of No. 4 tube about 6 inches long, close one end, smooth the other, and allow it to cool. Take another piece 3 inches long, close one end, and allow it to cool.

Now make a hole in the side of the first tube at a point 3 inches from the closed end. Do this as described in the last experiment but leave the hole projecting beyond the side of the tube (1, Fig. 76).

FIG. 80

MAKING A Y

Now heat the edge of the hole and the end of the short piece in the lamp flame, and make a joint (2, Fig. 76) exactly as described in Experiment 53. Be particular to heat and blow all around the joint at least three times to make the glass uniform, and on the last blowing leave the joint a little larger than the tube. Cut off the closed ends, make the arms equal in length, smooth the ends, and your tee is made (3, Fig. 76).

Your first attempt may not be beautiful, but if you will repeat the heating and gentle blowing often enough, the joint will be strong, which is the main point.

Repeat until you can make a tee easily.

Make a tee with No. 2 tubing.

Your flame is hardly large enough to make a tee with No. 6 tubing.

Experiment 57. A three-armed siphon.

Make a three-armed siphon as shown in Fig. 77. Put two arms in tumblers filled with water, suck air out of the third arm until the water runs, and then put it in an empty tumbler.

Stand the three tumblers on the table. Does the water run until the levels are the same?

Put one tumbler on a book. Does the water run into the other two tumblers until the levels are the same?

Return the one tumbler to the table and put the other two on the book. Does the water run from both tumblers to the lower tumbler until the levels are again the same?

Experiment 58. To make a repeating air gun.

FIG. 81

BALANCING COLUMNS

Take a full length of No. 4 tubing, put a branch about 3 inches long at a point about 2 inches from one end; leave the end of the branch closed (Fig. 78). Now load the branch with shot or coarse dry sand, and your repeating air gun is ready for use.

Tilt the branch slightly above the horizontal and blow intermittently. Does your gun reload after each blow, until the ammunition is used up?

Experiment 59. To make a four-way junction.

Make a tee as in Experiment 56, but do not cut off the closed ends. Now attach a fourth arm, as in Fig. 79, and heat and blow gently as before to work the glass into uniform condition. Cut off the closed arms at equal lengths, smooth the ends, and your four-way junction is made.

Experiment 60. A four-arm siphon.

Make a four-arm siphon, repeat the experiments described in Experiment 57, and make others of your own.

Experiment 61. To make a Y.

Make a tee as in Experiment 56, then make a bend about ½ inch from the stem on each side (Fig. 80), and your Y is complete.

Experiment 62. Balancing columns.

Arrange the apparatus as in Fig. 81, put the arms together in a glass of water, suck a little air out of the top coupling and close it with a glass plug. Do you find that the water rises to the same level in each?

Place the arms in separate tumblers filled with water to the same level and repeat. Does the water rise to the same level?

FIG. 82

THE WATER LEVELS ARE THE SAME

Add an extra length to one arm and repeat. Are the levels different but are they equal distances above the water in their respective tumblers?

Place the tumblers on the table, make one tube slanting, and repeat the experiment (Fig. 82). Are the levels again the same?

When you suck air out of the tee, you decrease the air pressure in the two tubes, and the atmospheric pressure on the water in the tumblers lifts the water into the tubes.

Experiment 63. Unequal columns.

Put a large handful of salt into a tumbler partly filled with water and stir until the salt is dissolved. Now pour fresh water into another tumbler until it is at the same height as the salt water. Make the arms of equal length, put one arm in the salt water and the other in the fresh water, then suck a little air out of the top coupling and close it with a plug. Do you find that the column of salt water is shorter than the column of fresh water (1, Fig. 83)? It is shorter because salt water is heavier than fresh water.

FIG. 83

UNEQUAL COLUMNS

If you have gasoline or kerosene convenient fill one tumbler half full of either, and the other tumbler half full of water, then repeat the experiment. Do you find that the column of gasoline or kerosene is longer than the column of water (2, Fig. 83)? It is longer because gasoline and kerosene are lighter than water.

Experiment 64. To fuse wire into glass.

Find a piece of thin iron or copper wire about 4 inches long, heat the end of a piece of No. 2 tubing until it is nearly closed, insert the iron or copper wire into the small hole, and heat the glass around the wire until it shrinks and grips the wire firmly (Fig. 84). The glass then serves as a handle for the wire.

FIG. 84

WIRE FUSED INTO GLASS

It is difficult to make a secure joint between iron or copper wire and glass because they both expand and contract more than glass when heated and cooled. It is easy to make a secure joint between platinum wire and glass because platinum and glass expand and contract at practically the same rate when heated and cooled. Platinum, however, is too expensive to be used for ordinary experiments.

Experiment 65. To cut window glass.

The common glass cutter is a small very hard steel wheel mounted on a handle (Fig. 85). Practice with one on a pane of glass: place a ruler on the glass, draw the wheel along the ruler (Fig. 86) with sufficient pressure to scratch the glass, place the under side of the scratch exactly over the edge of the table, and press down on both sides.

FIG. 85

A GLASS CUTTER

Experiment 66. To bore a hole in glass.

FIG. 86

CUTTING A PANE OF GLASS

Place a piece of window glass flat on the table, pour a little kerosene on the spot to be bored, clasp the file near the end, press the end down hard on the spot and turn it back and forth with a gouging motion (Fig. 87). You twist the file just as you would twist an awl to force it into hard wood.

You will soon penetrate the surface; use plenty of kerosene and continue the boring until you are nearly through; then turn the plate over and start a hole on the other side to meet the one you have made.

FIG. 87

BORING A HOLE IN GLASS

Do not rush things; it will take you ten or fifteen minutes to bore through ordinary window glass.

Bore a hole in a bottle in the same way, except that the boring is all from the outside.

If the end of the file becomes dull, break off a small piece, with a pair of pliers, to expose a fresh surface.

Experiment 67. To cut a bottle in two.

FIG. 88

BOTTLE READY TO BE CUT IN TWO

Wind a strip of blotting-paper or wrapping paper 2 inches wide around the bottle at one side of the line along which you wish to cut. Make three or more thicknesses and then tie the paper with cord within ½ inch of the edge to be cut. Wrap another similar piece on the opposite side of the place to be cut and ³⁄₁₆ inch from the first piece (Fig. 88).

FIG. 89

HEATING THE BOTTLE

Now stand the bottle in a pail of water until the paper is thoroughly wet (about five minutes), take it out, rotate it in a horizontal position and direct the blowpipe flame against the glass between the papers (Fig. 89).

Continue this for four or five minutes, then if the bottle has not dropped apart, plunge it vertically into the pail of water.

The bottle will break into two parts along the line between the two papers (Fig. 90). If it does not do so, repeat the operation until it does. Smooth the rough edges outside and inside with the file. You cannot do this with the flame because the glass is too brittle.

FIG. 90

THE BOTTLE CUT IN TWO

Experiment 68. To grind glass.

Rough edges of glass can be ground smooth by means of emery paper. For example, to smooth the edges of the glass bottle you have just cut in two, use the file for the rough work, then lay a piece of emery paper on a plate of glass, emery side up, pour a little kerosene on it and rub the rough surface on the emery with a rotary motion (Fig. 91). Finish with fine emery paper, and smooth the edges inside and out with the fine paper.

FIG. 91

SMOOTHING THE EDGES

Experiment 69. To cement glass.

There are two important points to remember in cementing glass: first, to get the glass clean, and second, to press the surfaces together after applying the cement, to squeeze out as much of the cement as possible, and to keep them pressed together until the cement is hard. To clean the glass wash it thoroughly with soap and water, rinse, and dry with a clean cloth.

FIG. 92

CEMENTING GLASS

There are many excellent glass cements on the market. Some of these are solid and are used only on hot glass; others are liquid and are used on cold or hot glass.

Cement two strips of glass together (Fig. 92) with sealing wax or solid shellac or some other solid cement as follows: Clean the glass thoroughly, place in the oven or on the stove, heat gradually until the glass just melts the cement, rub the cement over both surfaces, bring them together when the cement is fluid, press them together to squeeze out as much cement as possible, and keep them pressed together until the cement is hard.

Cement a strip of wood to a strip of glass in the same way.

Cement a strip of wood to a strip of glass with liquid glue, both wood and glass being cold. Keep them pressed together until the glue is dry, perhaps a day or two.

MAGICAL EXPERIMENTS

Boys, you can perform many magic experiments with apparatus made out of the glass tubes, rubber stoppers, and rubber unions supplied with “Experimental Glass Blowing.” We outline a number in the following pages. You can invent many more for yourselves.

MAGIC WITH FLAMES

Experiment 70. Magic lighting.

Light your alcohol lamp, blow it out, and bring a lighted match down toward the wick from above (Fig. 93). Does the lamp light in a most magical manner before the match touches the wick?

FIG. 93

MAGIC

Repeat this with a kerosene lamp and with a candle. Do they light in the same magical manner?

The “why” of it

When the lamp is lighted, the alcohol or kerosene turns to a gas, and it is the gas which burns; when the candle is lighted, the wax turns to an oil, the oil turns to a gas, and it is the gas which burns.

The gas rises from the wick for a short time after the flame is blown out, and it is this gas which lights when you bring the match down toward the wick.

Experiment 71. Air used by flames.

FIG. 94

THE CANDLES GO OUT AND THE WATER RISES

Drop melted candle wax on a tin can cover and attach the bottoms of two candles to the cover (Fig. 94); use one candle about 4 inches long and another about 3 inches, stand them upright in a pan of water, light them, and invert a wide-mouthed bottle over them. Does some air escape at first due to expansion, do both candles go out, the taller one first, and does the water rise until the bottle is about one-fifth full?

FIG. 95

THE CORK RISES

Cut a piece of candle ½ inch long, float it on a flat cork or can cover in the pan of water, light it, and invert a fresh empty bottle over it (Fig. 95). Is the result similar?

The “why” of it

The water rises in the bottle because ⅕ of the air is used up by the burning candle. Air is ⅕ oxygen and ⅘ nitrogen. The oxygen unites with the burning gas of the candle and produces water vapor (H_2O) and carbon dioxide (CO_2); the nitrogen takes no part in the burning.

FIG. 96

WATER FROM FLAME

The water vapor (H_2O) condenses to water on cooling and takes up very little space. The carbon dioxide remains a gas and occupies space, but this is offset by the volume of the air which escaped at first. The result is that the volume of gas at the end is about ⅕ less, and the atmospheric pressure on the water in the pan lifts water into the bottle.

The candle goes out because it must have oxygen to burn and the oxygen is used up.

Experiment 72. Water produced by fire.

It is certainly magic to produce water from fire, but you can do it easily as follows: Hold a clean, dry, cold tumbler over your alcohol lamp flame (Fig. 96). Does water deposit in the form of mist on the inside of the tumbler?

FIG. 97

ATMOSPHERIC PRESSURE

Repeat with fresh tumblers with the flame of a kerosene lamp and of a candle. Are the results similar?

Direct the blowpipe flame into the end of a piece of No. 2 or 4 tubing. Does water deposit in drops inside the tube about 1 inch above the end?

The “why” of it

One of the chief constituents of alcohol, kerosene, and candle wax is hydrogen (H), and when this burns in the oxygen (O) of the air, it produces water (H_2O). It is this water which condenses on the cold glass.

MAGIC WITH AIR

Experiment 73. Atmospheric pressure.

Arrange a No. 6 tube as in 1, Fig. 97, and suck air out at the top. Does the water run uphill into your mouth?

Hold your finger over the top and lift the tube out of the pail (2). Does the water remain in the tube? Fill a bottle with water to overflowing, insert a No. 2 tube into your one-hole stopper, insert the stopper into the mouth of the bottle (3) without admitting air below the stopper, and try to suck water out of the bottle. Do you find that you cannot do so?

FIG. 98

WATER DRIVEN UP TUBE BY ATMOSPHERE

Repeat (3) with the bottle half full of air (4). Do you find that you can now suck part of the water out of the bottle, and all of it if you admit air?

The “why” of it

The atmosphere which surrounds the earth exerts a pressure of 15 pounds per square inch on everything at the earth’s surface. It exerts this pressure equally downward, sidewise, and upward.

It is this atmospheric pressure on the water in the pail (1) which lifts the water into the tube when you decrease the pressure on the water in the tube by sucking out air and then water.

It is this pressure upward that supports the water in 2.

The water does not rise in 3 because the atmosphere cannot exert pressure downward on the water in the bottle.

FIG. 99

A FOUNTAIN

The rise of the water in 4 is due to another fact, namely, that any gas expands when the pressure on it is decreased. When you suck air out of the tube you decrease the pressure on the water in the tube and thereby on the air in the bottle; the air then expands and lifts the water into your mouth.

Experiment 74. Great pressure of air.

With the apparatus Fig. 98 hold your finger over the lower end of the tube, suck as much air as you can out of the tube, pinch the coupling, and remove your finger under water. Does the atmosphere drive water up the tube very rapidly and with great force?

FIG. 100

MAGIC

Experiment 75. A fountain.

With the apparatus Fig. 99 suck as much air as you can out of the bottle, pinch the coupling, and open it under water. Does the atmosphere lift the water into the bottle and produce a beautiful fountain?

FIG. 101

MORE MAGIC

Experiment 76. Magic tumbler.

Fill a tumbler with water, cover it with a sheet of paper, hold the paper on with your hand, invert the tumbler, and remove your hand (Fig. 100). Does the atmospheric pressure upward support the paper and water?

Experiment 77. Magic lift.

Fill a tumbler with water, press your palm down on the top with your fingers pointing downward (Fig. 101), straighten your fingers without admitting air to the tumbler, and then lift your hand. Do you lift the tumbler of water also?

There is a partial vacuum between your hand and the water, and the atmospheric pressure upward and downward holds your hand and the tumbler together.

FIG. 102

TUMBLER PENDULUM

Experiment 78. A magic pendulum.

Pass a string through a small hole in a piece of cardboard, knot the end of the string, and drop melted candle wax over the hole to make it air tight.

Fill a tumbler with water, press the cardboard down on the tumbler with the palm of your hand, and lift the string. Do you also lift the tumbler (Fig. 102)?

Swing the tumbler gently as a pendulum.

FIG. 103

POULTRY FOUNTAIN

Experiment 79. A poultry fountain.

To make the poultry fountain (Fig. 103), fill a bottle with water, hold your thumb over the mouth, invert the bottle over the pan of water, and remove your thumb under water. Does the atmospheric pressure on the water in the pan hold the water in the bottle?

Lift the bottle until the mouth is a little above the water in the pan. Does air enter and water run out until the mouth is again covered with water? This is what happens when the poultry, by drinking, lower the water below the mouth of the bottle.

In a poultry fountain the bottle is supported, as shown, with its mouth under water but above the bottom.

FIG. 104

A DRINKING FOUNTAIN

(From Butler’s Household Physics. Published by Whitcomb & Barrows, Boston)

FIG. 105

HOMEMADE DRINKING FOUNTAIN

Experiment 80. A drinking fountain.

The drinking fountain (Fig. 104) is similar in principle to the poultry fountain of the last experiment. The water is held in the large inverted bottle by the atmospheric pressure on the water in the lower vessel. Air enters the bottle and water escapes from it when the level of the water in the lower vessel falls below the mouth of the bottle. The water is cooled by the ice surrounding the lower vessel.

Make a drinking fountain of this kind as in Fig. 105, ask a friend to hold it, remove the glass plug from the coupling, and draw a glass of water. Do you observe that air bubbles enter the inverted bottle and water flows from it only when the water level in the half bottle falls below the mouth of the inverted bottle?

Allow the water to flow continuously. Is the water level practically constant in the half bottle until the upper bottle is empty?

TRANSCRIBER’S NOTES

- Typos fixed; non-standard spelling and dialect retained.

*** END OF THE PROJECT GUTENBERG EBOOK EXPERIMENTAL GLASS BLOWING FOR BOYS ***

Updated editions will replace the previous one—the old editions will be renamed.

Creating the works from print editions not protected by U.S. copyright law means that no one owns a United States copyright in these works, so the Foundation (and you!) can copy and distribute it in the United States without permission and without paying copyright royalties. Special rules, set forth in the General Terms of Use part of this license, apply to copying and distributing Project Gutenberg™ electronic works to protect the PROJECT GUTENBERG™ concept and trademark. Project Gutenberg is a registered trademark, and may not be used if you charge for an eBook, except by following the terms of the trademark license, including paying royalties for use of the Project Gutenberg trademark. If you do not charge anything for copies of this eBook, complying with the trademark license is very easy. You may use this eBook for nearly any purpose such as creation of derivative works, reports, performances and research. Project Gutenberg eBooks may be modified and printed and given away—you may do practically ANYTHING in the United States with eBooks not protected by U.S. copyright law. Redistribution is subject to the trademark license, especially commercial redistribution.

START: FULL LICENSE

THE FULL PROJECT GUTENBERG LICENSE

PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK

To protect the Project Gutenberg™ mission of promoting the free distribution of electronic works, by using or distributing this work (or any other work associated in any way with the phrase “Project Gutenberg”), you agree to comply with all the terms of the Full Project Gutenberg™ License available with this file or online at www.gutenberg.org/license.

Section 1. General Terms of Use and Redistributing Project Gutenberg™ electronic works

1.A. By reading or using any part of this Project Gutenberg™ electronic work, you indicate that you have read, understand, agree to and accept all the terms of this license and intellectual property (trademark/copyright) agreement. If you do not agree to abide by all the terms of this agreement, you must cease using and return or destroy all copies of Project Gutenberg™ electronic works in your possession. If you paid a fee for obtaining a copy of or access to a Project Gutenberg™ electronic work and you do not agree to be bound by the terms of this agreement, you may obtain a refund from the person or entity to whom you paid the fee as set forth in paragraph 1.E.8.

1.B. “Project Gutenberg” is a registered trademark. It may only be used on or associated in any way with an electronic work by people who agree to be bound by the terms of this agreement. There are a few things that you can do with most Project Gutenberg™ electronic works even without complying with the full terms of this agreement. See paragraph 1.C below. There are a lot of things you can do with Project Gutenberg™ electronic works if you follow the terms of this agreement and help preserve free future access to Project Gutenberg™ electronic works. See paragraph 1.E below.

1.C. The Project Gutenberg Literary Archive Foundation (“the Foundation” or PGLAF), owns a compilation copyright in the collection of Project Gutenberg™ electronic works. Nearly all the individual works in the collection are in the public domain in the United States. If an individual work is unprotected by copyright law in the United States and you are located in the United States, we do not claim a right to prevent you from copying, distributing, performing, displaying or creating derivative works based on the work as long as all references to Project Gutenberg are removed. Of course, we hope that you will support the Project Gutenberg™ mission of promoting free access to electronic works by freely sharing Project Gutenberg™ works in compliance with the terms of this agreement for keeping the Project Gutenberg™ name associated with the work. You can easily comply with the terms of this agreement by keeping this work in the same format with its attached full Project Gutenberg™ License when you share it without charge with others.

1.D. The copyright laws of the place where you are located also govern what you can do with this work. Copyright laws in most countries are in a constant state of change. If you are outside the United States, check the laws of your country in addition to the terms of this agreement before downloading, copying, displaying, performing, distributing or creating derivative works based on this work or any other Project Gutenberg™ work. The Foundation makes no representations concerning the copyright status of any work in any country other than the United States.

1.E. Unless you have removed all references to Project Gutenberg:

1.E.1. The following sentence, with active links to, or other immediate access to, the full Project Gutenberg™ License must appear prominently whenever any copy of a Project Gutenberg™ work (any work on which the phrase “Project Gutenberg” appears, or with which the phrase “Project Gutenberg” is associated) is accessed, displayed, performed, viewed, copied or distributed:

This eBook is for the use of anyone anywhere in the United States and most other parts of the world at no cost and with almost no restrictions whatsoever. You may copy it, give it away or re-use it under the terms of the Project Gutenberg License included with this eBook or online at www.gutenberg.org. If you are not located in the United States, you will have to check the laws of the country where you are located before using this eBook.

1.E.2. If an individual Project Gutenberg™ electronic work is derived from texts not protected by U.S. copyright law (does not contain a notice indicating that it is posted with permission of the copyright holder), the work can be copied and distributed to anyone in the United States without paying any fees or charges. If you are redistributing or providing access to a work with the phrase “Project Gutenberg” associated with or appearing on the work, you must comply either with the requirements of paragraphs 1.E.1 through 1.E.7 or obtain permission for the use of the work and the Project Gutenberg™ trademark as set forth in paragraphs 1.E.8 or 1.E.9.

1.E.3. If an individual Project Gutenberg™ electronic work is posted with the permission of the copyright holder, your use and distribution must comply with both paragraphs 1.E.1 through 1.E.7 and any additional terms imposed by the copyright holder. Additional terms will be linked to the Project Gutenberg™ License for all works posted with the permission of the copyright holder found at the beginning of this work.

1.E.4. Do not unlink or detach or remove the full Project Gutenberg™ License terms from this work, or any files containing a part of this work or any other work associated with Project Gutenberg™.

1.E.5. Do not copy, display, perform, distribute or redistribute this electronic work, or any part of this electronic work, without prominently displaying the sentence set forth in paragraph 1.E.1 with active links or immediate access to the full terms of the Project Gutenberg™ License.

1.E.6. You may convert to and distribute this work in any binary, compressed, marked up, nonproprietary or proprietary form, including any word processing or hypertext form. However, if you provide access to or distribute copies of a Project Gutenberg™ work in a format other than “Plain Vanilla ASCII” or other format used in the official version posted on the official Project Gutenberg™ website (www.gutenberg.org), you must, at no additional cost, fee or expense to the user, provide a copy, a means of exporting a copy, or a means of obtaining a copy upon request, of the work in its original “Plain Vanilla ASCII” or other form. Any alternate format must include the full Project Gutenberg™ License as specified in paragraph 1.E.1.

1.E.7. Do not charge a fee for access to, viewing, displaying, performing, copying or distributing any Project Gutenberg™ works unless you comply with paragraph 1.E.8 or 1.E.9.

1.E.8. You may charge a reasonable fee for copies of or providing access to or distributing Project Gutenberg™ electronic works provided that:

- • You pay a royalty fee of 20% of the gross profits you derive from the use of Project Gutenberg™ works calculated using the method you already use to calculate your applicable taxes. The fee is owed to the owner of the Project Gutenberg™ trademark, but he has agreed to donate royalties under this paragraph to the Project Gutenberg Literary Archive Foundation. Royalty payments must be paid within 60 days following each date on which you prepare (or are legally required to prepare) your periodic tax returns. Royalty payments should be clearly marked as such and sent to the Project Gutenberg Literary Archive Foundation at the address specified in Section 4, “Information about donations to the Project Gutenberg Literary Archive Foundation.”

- • You provide a full refund of any money paid by a user who notifies you in writing (or by e-mail) within 30 days of receipt that s/he does not agree to the terms of the full Project Gutenberg™ License. You must require such a user to return or destroy all copies of the works possessed in a physical medium and discontinue all use of and all access to other copies of Project Gutenberg™ works.

- • You provide, in accordance with paragraph 1.F.3, a full refund of any money paid for a work or a replacement copy, if a defect in the electronic work is discovered and reported to you within 90 days of receipt of the work.

- • You comply with all other terms of this agreement for free distribution of Project Gutenberg™ works.

1.E.9. If you wish to charge a fee or distribute a Project Gutenberg™ electronic work or group of works on different terms than are set forth in this agreement, you must obtain permission in writing from the Project Gutenberg Literary Archive Foundation, the manager of the Project Gutenberg™ trademark. Contact the Foundation as set forth in Section 3 below.

1.F.

1.F.1. Project Gutenberg volunteers and employees expend considerable effort to identify, do copyright research on, transcribe and proofread works not protected by U.S. copyright law in creating the Project Gutenberg™ collection. Despite these efforts, Project Gutenberg™ electronic works, and the medium on which they may be stored, may contain “Defects,” such as, but not limited to, incomplete, inaccurate or corrupt data, transcription errors, a copyright or other intellectual property infringement, a defective or damaged disk or other medium, a computer virus, or computer codes that damage or cannot be read by your equipment.

1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the “Right of Replacement or Refund” described in paragraph 1.F.3, the Project Gutenberg Literary Archive Foundation, the owner of the Project Gutenberg™ trademark, and any other party distributing a Project Gutenberg™ electronic work under this agreement, disclaim all liability to you for damages, costs and expenses, including legal fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE PROVIDED IN PARAGRAPH 1.F.3. YOU AGREE THAT THE FOUNDATION, THE TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH DAMAGE.

1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a defect in this electronic work within 90 days of receiving it, you can receive a refund of the money (if any) you paid for it by sending a written explanation to the person you received the work from. If you received the work on a physical medium, you must return the medium with your written explanation. The person or entity that provided you with the defective work may elect to provide a replacement copy in lieu of a refund. If you received the work electronically, the person or entity providing it to you may choose to give you a second opportunity to receive the work electronically in lieu of a refund. If the second copy is also defective, you may demand a refund in writing without further opportunities to fix the problem.

1.F.4. Except for the limited right of replacement or refund set forth in paragraph 1.F.3, this work is provided to you ‘AS-IS’, WITH NO OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.

1.F.5. Some states do not allow disclaimers of certain implied warranties or the exclusion or limitation of certain types of damages. If any disclaimer or limitation set forth in this agreement violates the law of the state applicable to this agreement, the agreement shall be interpreted to make the maximum disclaimer or limitation permitted by the applicable state law. The invalidity or unenforceability of any provision of this agreement shall not void the remaining provisions.

1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the trademark owner, any agent or employee of the Foundation, anyone providing copies of Project Gutenberg™ electronic works in accordance with this agreement, and any volunteers associated with the production, promotion and distribution of Project Gutenberg™ electronic works, harmless from all liability, costs and expenses, including legal fees, that arise directly or indirectly from any of the following which you do or cause to occur: (a) distribution of this or any Project Gutenberg™ work, (b) alteration, modification, or additions or deletions to any Project Gutenberg™ work, and (c) any Defect you cause.

Section 2. Information about the Mission of Project Gutenberg™

Project Gutenberg™ is synonymous with the free distribution of electronic works in formats readable by the widest variety of computers including obsolete, old, middle-aged and new computers. It exists because of the efforts of hundreds of volunteers and donations from people in all walks of life.

Volunteers and financial support to provide volunteers with the assistance they need are critical to reaching Project Gutenberg™’s goals and ensuring that the Project Gutenberg™ collection will remain freely available for generations to come. In 2001, the Project Gutenberg Literary Archive Foundation was created to provide a secure and permanent future for Project Gutenberg™ and future generations. To learn more about the Project Gutenberg Literary Archive Foundation and how your efforts and donations can help, see Sections 3 and 4 and the Foundation information page at www.gutenberg.org.

Section 3. Information about the Project Gutenberg Literary Archive Foundation

The Project Gutenberg Literary Archive Foundation is a non-profit 501(c)(3) educational corporation organized under the laws of the state of Mississippi and granted tax exempt status by the Internal Revenue Service. The Foundation’s EIN or federal tax identification number is 64-6221541. Contributions to the Project Gutenberg Literary Archive Foundation are tax deductible to the full extent permitted by U.S. federal laws and your state’s laws.

The Foundation’s business office is located at 809 North 1500 West, Salt Lake City, UT 84116, (801) 596-1887. Email contact links and up to date contact information can be found at the Foundation’s website and official page at www.gutenberg.org/contact

Section 4. Information about Donations to the Project Gutenberg Literary Archive Foundation

Project Gutenberg™ depends upon and cannot survive without widespread public support and donations to carry out its mission of increasing the number of public domain and licensed works that can be freely distributed in machine-readable form accessible by the widest array of equipment including outdated equipment. Many small donations ($1 to $5,000) are particularly important to maintaining tax exempt status with the IRS.

The Foundation is committed to complying with the laws regulating charities and charitable donations in all 50 states of the United States. Compliance requirements are not uniform and it takes a considerable effort, much paperwork and many fees to meet and keep up with these requirements. We do not solicit donations in locations where we have not received written confirmation of compliance. To SEND DONATIONS or determine the status of compliance for any particular state visit www.gutenberg.org/donate.

While we cannot and do not solicit contributions from states where we have not met the solicitation requirements, we know of no prohibition against accepting unsolicited donations from donors in such states who approach us with offers to donate.

International donations are gratefully accepted, but we cannot make any statements concerning tax treatment of donations received from outside the United States. U.S. laws alone swamp our small staff.

Please check the Project Gutenberg web pages for current donation methods and addresses. Donations are accepted in a number of other ways including checks, online payments and credit card donations. To donate, please visit: www.gutenberg.org/donate.

Section 5. General Information About Project Gutenberg™ electronic works

Professor Michael S. Hart was the originator of the Project Gutenberg™ concept of a library of electronic works that could be freely shared with anyone. For forty years, he produced and distributed Project Gutenberg™ eBooks with only a loose network of volunteer support.

Project Gutenberg™ eBooks are often created from several printed editions, all of which are confirmed as not protected by copyright in the U.S. unless a copyright notice is included. Thus, we do not necessarily keep eBooks in compliance with any particular paper edition.

Most people start at our website which has the main PG search facility: www.gutenberg.org.

This website includes information about Project Gutenberg™, including how to make donations to the Project Gutenberg Literary Archive Foundation, how to help produce our new eBooks, and how to subscribe to our email newsletter to hear about new eBooks.

Table of Contents

Experimental Glass Blowing FOR BOYS

EXPERIMENTAL GLASS BLOWING

Experiment 1. Fun bending glass.

- THE LAMP

Experiment 2. To cut glass tubing.

Experiment 3. To make the edges smooth.

Experiment 4. Practice with the blowpipe.

Experiment 5. To close the end of a small tube.

- The “why” of it

Experiment 6. Fun blowing glass bubbles.

- BUBBLE COLORS

Experiment 7. To make water balloons.

Experiment 8. Magic.

Experiment 9. Balloon races.

- The “why” of it

Experiment 10. Fun with thin tubes.

Experiment 11. Magic.

- WHAT IS GLASS?
- HOW ARE THINGS MADE OF GLASS?
- WINDOW GLASS
- GLASS TUBES
- MOLDED GLASS
- PRESSED GLASS
- PLATE GLASS
- OPTICAL GLASS
- QUARTZ GLASS

Experiment 12. To make an acrobatic pollywog.

Experiment 13. Magic.

Experiment 14. A dancing pollywog.

Experiment 15. To make glass spider-web.

Experiment 16. The ancient spider trick.

Experiment 17. To make working handles.

Experiment 18. To close a large tube.

Experiment 19. To make a submarine.

Experiment 20. Magic.

Experiment 21. Fun with the submarine.

Experiment 22. A submarine battle.

Experiment 23. To flare the end of a tube.

Experiment 24. To make an air gun.

Experiment 25. A shooting match.

Experiment 26. Height and distance contest.

Experiment 27. To make a pea shooter.

Experiment 28. A pea-shooting match.

Experiment 29. To make a good bend.

Experiment 30. To make a drinking tube.

Experiment 31. To make a siphon.

Experiment 32. Magic.

Experiment 33. A long-armed siphon.

Experiment 34. To make a nozzle.

Experiment 35. To make a fountain.

Experiment 36. Magic.

Experiment 37. More magic.

Experiment 38. Still more magic.

Experiment 39. To start a siphon.

Experiment 40. To siphon sand or mud.

Experiment 41. To make a squirt bottle.

Experiment 42. To make a trick squirt bottle.

Experiment 43. Fun with a trick squirt bottle.

Experiment 44. To make an engineer’s level.

Experiment 45. To use the engineer’s level.

Experiment 46. To make a spirit level.

Experiment 47. To make a fountain-pen filler.

Experiment 48. To make a syringe.

Experiment 49. To make another syringe.

Experiment 50. To make a third syringe.

Experiment 51. To make a diablo whistle.

Experiment 52. Fun with the diablo whistle.

Experiment 53. To join two tubes end to end.

Experiment 54. To join tubes of different sizes.

Experiment 55. To make a large hole.

Experiment 56. To make a tee.

Experiment 57. A three-armed siphon.

Experiment 58. To make a repeating air gun.

Experiment 59. To make a four-way junction.

Experiment 60. A four-arm siphon.

Experiment 61. To make a Y.

Experiment 62. Balancing columns.

Experiment 63. Unequal columns.

Experiment 64. To fuse wire into glass.

Experiment 65. To cut window glass.

Experiment 66. To bore a hole in glass.

Experiment 67. To cut a bottle in two.

Experiment 68. To grind glass.

Experiment 69. To cement glass.

- MAGICAL EXPERIMENTS

- MAGIC WITH FLAMES

Experiment 70. Magic lighting.

- The “why” of it

Experiment 71. Air used by flames.

- The “why” of it

Experiment 72. Water produced by fire.

- The “why” of it

- MAGIC WITH AIR

Experiment 73. Atmospheric pressure.

- The “why” of it

Experiment 74. Great pressure of air.

Experiment 75. A fountain.

Experiment 76. Magic tumbler.

Experiment 77. Magic lift.

Experiment 78. A magic pendulum.

Experiment 79. A poultry fountain.

Experiment 80. A drinking fountain.

THE FULL PROJECT GUTENBERG LICENSE